CASE STUDY: K-Containment Seal and K-Snap-Loc

CASE STUDY:  K-Containment Seal and K-Snap-Loc from Kinder Australia Pty Ltd

By: Kinder Australia Pty Ltd  27-Apr-2016
Keywords: Material Handling Equipment, Conveyors, Conveyor

Product category: Conveyor Skirting & Sealing

Location: South-Western Victoria

Conveyed material: Wood Chip

Installation date: Jan 2016

Previous problem:

Repeating the same material spillage clean-up every week can feel like climbing a hill that gets steeper and longer with every step.

Even though you can plan to stop production so that the clean-up can be completed safely and when resources are to hand – it still doesn’t make it an efficient task. Allocating resources to deal with any spillage clean-up when they could otherwise be allocated to do more productive preventative maintenance is unproductive.

This was the problem that our wood chip customer was experiencing. The Maintenance Supervisor had estimated that the spillage was costing the company approximately $2000 each week to clean-up and take away.

Resolution:

Kinder Australia recommended the installation of K-Containment Seal to effectively contain the bulk wood chip material and handle the high internal chute pressure.

K-Containment Seal is a high performance, low friction engineered polyurethane system that provides exceptional resistance to wear. The slotted arrangement allows for installation adjustment to ensure that material cannot be entrapped leading to premature belt damage.

The K-Snap-Loc® Dust Seal System was also installed in combination with K-Containment Seal. This strong and very pliable polyurethane’s inherent “memory-set” applies efficient downward pressure on to the belt’s surface to create a fine tight seal without the need for any further manual adjustment.

“Since the installation on the 18th Jan, the site has not had to re visit or clean the area up. So in just 6 weeks already the company has saved more than $12K. The tower is still looking clean and doesn’t look to need any attention for some time.”

Keywords: Belt Conveyor Systems, Bulk Handling, Bulk Materials Handling, Conveyor, Conveyor Accessories, Conveyor Belt Supplies, Conveyor Components, Conveyor Hardware, Conveyor Suppliers, Conveyors, Kinder, Kinder Australia Pty Ltd, Material Handling Equipment,

Contact Kinder Australia Pty Ltd

Email

Print this page

Other examples of best work from Kinder Australia Pty Ltd

CASE STUDY:  K-Sure® Belt Support System from Kinder Australia Pty Ltd thumbnail
27-Apr-2016

CASE STUDY: K-Sure® Belt Support System

Once the belt was supported adequately, conveyor skirting can function along a flat, sag-free belt line. The K-Containment Seal is a high performance skirt system that offers exceptional resistance to wear. The slotted system arrangement extends its service life by allowing for further ongoing adjustment after initial installation. Since installation in July 2014 Ohau Quarry has had no issues with belt sag or belt damage and the same belt is still in operation coming up to 2 years later.


CASE STUDY:  K-Magna-Patch – Reusable Wear Repair Magnetic Patch from Kinder Australia Pty Ltd thumbnail
27-Apr-2016

CASE STUDY: K-Magna-Patch – Reusable Wear Repair Magnetic Patch

Because we didn’t need to allocate any additional emergency resources to this urgent repair task, which can cost approximately $1000 a day, this problem was resolved very cost-effectively as well as quickly.”


27-Apr-2016

CASE STUDY: K-Sure® Belt Support System

Kinder Australia then recommended the installation of the double layered K-Skirting Seal to trap the dust particles effectively. Mounted using shallow clamps it is ideal for this confined access location. This skirt works by utilising an interior wear resistant layer of polyurethane (longer lasting than rubber skirting), but it also has an outer anti-dust integral moulding that can adapt to belt vibration and maintain the correct pressure to effectively seal the belt.


CASE STUDY:  K-Containment Seal from Kinder Australia Pty Ltd thumbnail
27-Apr-2016

CASE STUDY: K-Containment Seal

K-Sure Belt Support, with its fixed low friction slider bars instead of moving rollers, was also installed directly under the transfer point, using adjustable frames to ensure exact angles. This is the ideal combination of seal and belt support and our customer is highly delighted with the sustainable outcome of this productivity improvement.


CASE STUDY:  K-Superline® Polyurethane Lining Sheet from Kinder Australia Pty Ltd thumbnail
27-Apr-2016

CASE STUDY: K-Superline® Polyurethane Lining Sheet

K-Superline has now completely eliminated material build up inside the feeder chute, and so has stopped the need for any jack-hammering on site. Our customer also observed that the K-Superline® provides 50% more wear life and so is completely delighted with their investment in a correctly specified durometer of K-Superline® high performance polyurethane sheet lining. Overall, our customer is seeing major cost gains from switching to K-Superline®.


CASE STUDY:  K-Skirting Seal from Kinder Australia Pty Ltd thumbnail
27-Apr-2016

CASE STUDY: K-Skirting Seal

Our customer confirmed that the change over and installation was not complicated and took the anticipated 2 resources to install as part of a planned maintenance schedule. K-Skirting Seal has not disappointed and lasts approximately 12 months in regular production and suppresses the dust more effectively.


CASE STUDY:  K-Superline ® Polyurethane Lining Sheet from Kinder Australia Pty Ltd thumbnail
27-Apr-2016

CASE STUDY: K-Superline ® Polyurethane Lining Sheet

K- Superline® has now been installed at the Dandenong site for 5 months and is showing no signs of wear. K-Superline® has exceeded our customer’s expectations of its durability potential.


CASE STUDY: Tru-Trac Conveyor Belt Tracking System – Yallourn, Victoria from Kinder Australia Pty Ltd thumbnail
19-Mar-2015

CASE STUDY: Tru-Trac Conveyor Belt Tracking System – Yallourn, Victoria

The Yallourn Power Station commenced operations in 1974 with four generating units commissioned between 1974 and 1982. Every hour 2,400 tonnes of brown coal is used to boil water into superheated steam to drive four turbine generators.


CASE STUDY : K-Sure® Belt Support System – Tauranga, New Zealand from Kinder Australia Pty Ltd thumbnail
19-Mar-2015

CASE STUDY : K-Sure® Belt Support System – Tauranga, New Zealand

This New Zealand based customer’s core business is based around their quarry activities. They are a major supplier of quarried products to the construction industry, with raw materials extracted and processed from over 40 different sites around the country.


CASE STUDY: K-Redi-Liner KP Dual Duro, Dromana from Kinder Australia Pty Ltd thumbnail
01-Sep-2014

CASE STUDY: K-Redi-Liner KP Dual Duro, Dromana

To resolve this problem, our customer favoured the features of K-Redi-Liner because it was lightweight in comparison to the bisalloy patches and also only needed to be bolted into place and not welded. Overall it required less labour to install which was meant that replacement costs were reduced.


CASE STUDY: K-Superline Polyurethane Lining Sheet - Brooklyn, Victoria from Kinder Australia Pty Ltd thumbnail
22-Jul-2014

CASE STUDY: K-Superline Polyurethane Lining Sheet - Brooklyn, Victoria

K- Superline® has now been installed at the Brooklyn site now for over 18 months and our customer is delighted to report that no signs of wear or tears from the aggregate have been observed


TEST REPORT: K-Superskirt Engineered Polyurethane from Kinder Australia Pty Ltd thumbnail
22-Jul-2014

TEST REPORT: K-Superskirt Engineered Polyurethane

Based on the results of the “Taber Test” by Excel Plas, the test conclusions confirmed that the Kinder & Co K-Superskirt® (red) polyurethane abrades less by comparison to the competitors (blue) polyurethane. The final result is further evidenced when tested at 50,000 cycles, wear index results showing 5.8 (red) compared to 25.92 (blue) or a ratio of 4.47: 1.


CASE STUDY: K-Snap-Loc Dust Seal System - North-West, Western Australia from Kinder Australia Pty Ltd thumbnail
22-Jul-2014

CASE STUDY: K-Snap-Loc Dust Seal System - North-West, Western Australia

Our customer has confirmed that the K-Snap-Loc Dust Seal System was very easy to install “only required measuring, and some welding of the stainless unistrut and did not require knocking down of skirts and adjustment. Kinder & Co provided lots of assistance in getting quotes, drawings, supplying offcuts of material from the warehouse and working with us to get our requirements right (stainless steel unistrut instead of the standard mild steel in stock).”


CASE STUDY: K-Impact Belt Support System - Geraldton, Western Australia from Kinder Australia Pty Ltd thumbnail
26-Feb-2014

CASE STUDY: K-Impact Belt Support System - Geraldton, Western Australia

Our ISO 9001 certified design and development process meant that the specification and manufacturing phase of this idea went smoothly and without error. Our customer is delighted with the final outcome.